Violin Forum/Message Board Forum Index Violin Forum/Message Board
Provided by Violin Vision
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

Stabilizing old spruce

 
Post new topic   Reply to topic    Violin Forum/Message Board Forum Index -> Violin Making and Restoration Forum
View previous topic :: View next topic  
Author Message
Dave Chandler
Super Member


Joined: 31 Oct 2007
Posts: 691
Location: Mt Mitchell in North Carolina

PostPosted: Sat Apr 02, 2016 5:59 pm    Post subject: Stabilizing old spruce Reply with quote

Im rebuilding an old factory violin labelled Mathias Thier in Wien 186x. Had a hairball the size of a nickel. Many earlier repairs inside the top. The wood is so fragile, I think the top is nearing its end. Thinking of coating it with something to give it some additional life. Recommendations?

Thinned clear shellac?
Thinned lacquer?
Egg white?
_________________
Dave in the Blue Ridge
Southern Violin Association

"Success is the ability to go from one failure to the next with no loss of enthusiasm" Winston Churchill

"I took the road less travelled, and now I don't know where I am." Marco Polo
Back to top
View user's profile Send private message Send e-mail Visit poster's website AIM Address
Michael Darnton
Moderator


Joined: 23 Mar 2007
Posts: 1347
Location: Chicago

PostPosted: Sun Apr 03, 2016 8:12 am    Post subject: Reply with quote

Don't! I've seen this several times and had to remove it each time to do more repairs because the coating was in the way or had failed.

in the worst case someone had used hide glue over the whole inside and the top distorted. In another case someone had lined the edges with glued in layers of silk which made a mess and had to be taken out just to get to the wood underneath. Both shellac and lacquer will repell further gluing of cleats or patches.

If you feel the need to do something, use very thin reinforcing studs carefully fitted only where they will do the most good, and don't line their edges up or you will create a stress riser and cause new cracks.

Probably, though, leaving it alone is best: unless there's a strong tonal problem to correct, you may create one, instead.
_________________
new blog at my site! http://darntonviolins.com/blog
my work sites: http://darntonviolins.com and http://darntonhersh.com
Back to top
View user's profile Send private message Send e-mail Visit poster's website
Dave Chandler
Super Member


Joined: 31 Oct 2007
Posts: 691
Location: Mt Mitchell in North Carolina

PostPosted: Sun Apr 03, 2016 9:44 am    Post subject: Reply with quote

Thanks Michael. It had an ugly dark film all over inside top, most of which I sanded off. Cleats installed long ago dropping off, glue had released from the wood, perhaps as you said someone long ago sealed the interior with something causing the condition. No idea of tone, its been in pieces for many years.
_________________
Dave in the Blue Ridge
Southern Violin Association

"Success is the ability to go from one failure to the next with no loss of enthusiasm" Winston Churchill

"I took the road less travelled, and now I don't know where I am." Marco Polo
Back to top
View user's profile Send private message Send e-mail Visit poster's website AIM Address
Display posts from previous:   
Post new topic   Reply to topic    Violin Forum/Message Board Forum Index -> Violin Making and Restoration Forum All times are GMT - 4 Hours
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group